VSD Auto Pop-hole Door Openers

The new VSD Auto Pop-hole Door Opener for Chicken Coops.

This Vertical Sliding Door Opener is perfect for Chicken Coop Pop-hole Doors and has been brought bang up to date for 2019 with new features and an improved slimline layout inside.

Can be mounted outside or inside the henhouse. For internal use add the EXTERNAL LIGHT SENSOR

The VSD, like the VSB, is a battery powered Electronic Chicken Coop Door Opener and the redesign now includes more options e.g. replaceable on-board light sensor; the manual override function; slimline casing; additional pins to add mains power, timers and external sensors/indicators. Batteries are included.

The VSD can be mounted on the outside of your chicken house above the sliding pop-hole door (or can be offset with pulleys where space is an issue). We suggest the sliding door is the aluminium option (below) to ensure it remains free-moving throughout the year but, you can add the VSD to a wooden vertical door as long as it moves up and down freely. The maximum weight of the door must not exceed 3kg. The cord is very strong with a 40lb breaking strain.

Once set and batteries inserted the VSD will open the door at dawn and close it at dusk by means of a strong cord attached to the pop-hole door. An LED indicator in the lower right will show green for closed and OK, and it will show red if there is an error or battery change needed. A Battery Powered Timer can also be added to give control of opening and/or closing using timed settings.

To manually override the door closing/opening, a red magnet is supplied to touch at the base of the VSD casing and activate the motor to raise or lower the door.

For internal mounting you would place the VSD inside the coop above the pop-hole and add the remote light sensor which connects to two pins on the circuit board. This sensor remotely takes the light levels outside the henhouse to activate the unit inside.

Dimensions: 125mm x 125mm x 50mm. Batteries are included with the VSD as well as comprehensive instructions for installation making this a very simple to do. No electronic or specialist knowledge needed at all. We offer telephone back up for trouble shooting if required though.

FSF Note: the red magnet is quite small so we advise tying a coloured cord/ribbon to it in case you drop it on the ground (makes it easier to find and can also be hung near the VSD perhaps), otherwise it may get lost.

People who bought this item also bought:

1. Lightweight Pop-hole Door for Auto Door Openers (Ref: VSBDOOR)

2. External Light Sensor Cable for VSB & VSD Units (Ref: VSBAS)

3. Digital Battery Timer for VSB & VSD Door Openers (Ref: BTVSB-D)

External Light Sensor Cable for old VSB, and new VSD Chicken House Door Opener Units.

If you want to convert a VSD (or the old VSB) Door Opener to for internal use then this is the cable you need, or, if you just need to replace an existing cable.

The cable is exactly 1m in length and houses a photo cell in one end, also included is a black cap for covering the photo cell on the circuit board inside the unit. You simply attach the cable to two of the pins inside the VSB/VSD box and cover the internal light sensor on the circuit board. Then, fix the external light sensor (bulb) on the outside of your house and it will then close the door at dusk.

Light Sensors carry a one year warranty.

(FSF note: for purchases of sensor cable made after 2nd June 2017 the new cable will have a blue stripe around the end senosr. In this case the wires need to be connected thus: white wire to Pin 6 and brown wire to Pin 5)

Related products:

1. VSB Automatic Pop-hole Door Opener - external (Ref: VSBb)

2. Replacement battery holder for VSB Units (Ref: VSB-BH)

3. Large Pulley for VSB & VSD Pop-hole Door Openers (Ref: VSBHS2)

People who bought this item also bought:

1. VSD Auto Pop-hole Door Opener (Ref: AXT-VSDb)

2. Lightweight Pop-hole Door for Auto Door Openers (Ref: VSBDOOR)

3. Spare Cord for VSB & VSD units, 2m (Ref: VSBC)

An External Manual Control Cable for VSD Units, 1m long, with a red sensor end. NOT suitable for VSB units.

The manual control cable is specifically for the VSD Door Opener Units (and VSE) to be able to remotely override the opening and closing of these Automatic Pop-Hole Dooor Openers.

This cable is connected to the internal circuit board of the VSD unit on to pins 8 (white cable) at the bottom and pin 7 (brown cable) above.

Use this cable in the case of an internally mounted VSD unit, where access to the unit may be restricted, to allow you to use the red magnet - that would normally be held up to the VSD to override - to be placed up to the sensor and close or open the door.

People who bought this item also bought:

1. VSD Auto Pop-hole Door Opener (Ref: AXT-VSDb)

2. Feeder Shelter or Dustbath (Ref: FSDB)

3. Dorset Ranger Ten Chicken Coop with 9ft Run (Ref: RNGR1009)

Status Indicator Cable with Green LED for use with VSD units (with green band on sensor). This cable replicates the status flashes normally seen on the VSD unit but if your VSD is mounted inside the Coop it won't be visible. NOT suitable for VSB units.

Add this to your door opener set up so you can see the status of the VSD unit externally or from a distance. Green flash indicates door closed and all is ok; one Red flash indicates door blockage; 2 Red flashes shows batteries need replacing and 3 Red flashes shows a problem with the cord or an overload.

Attach the cables to Pins 9 and 10 inside the VSD unit (white cable to Pin 10 and brown cable to Pin 9). Place the LED through a 9mm hole to the outside of the coop so that it is easily visible. The Cable is 1m long.

Lightweight Aluminium Door with two metal runners for use with the VSB internal or external Door Openers as well as the Chicken Guard Door openers. Three sizes available.

This metal door, being aluminium, will not rust over time and also, unlike many wooden pop-hole doors will not warp, swell or twist in the runners.

Can be fitted inside or outside your chicken house depending on space available. Consists of two aluminium, H profile, runners and one flat aluminium door (as this is aluminium you can cut the door and runners down to a custom size if required).

Select size required from drop down box above.
Small size - to fit pop-holes up to 22cm wide x 33cm high - 275g (runners are 60cm tall)
Medium size - to fit pop-holes up to 30cm wide x 40cm high - 470g (runners are 70cm tall)
Large size - to fit pop-holes up to 33cm wide x 50cm high - 648g (runners are 80cm tall)

FSF Guide: Maggie's Six and Dozen Henhouses use a Medium Door (owing to the size of the pop-hole on the Maggie's 24 we have to make a lightweight wooden door to fit - please state during ordering if for a Maggie's 24). Hobby Henhouses use a Medium Door. We have also put together complete kits of VSB and door plus any necessary timbers for our houses, see

Related products:

1. VSB Automatic Pop-hole Door Opener - external (Ref: VSBb)

2. Chicken Guard Automatic Door Opener - Standard AS (Ref: CGUARD-AS)

3. Large Pulley for VSB & VSD Pop-hole Door Openers (Ref: VSBHS2)

4. VSB Automatic Pop-hole Door Opener - internal (Ref: VSBbi)

People who bought this item also bought:

1. VSD Auto Pop-hole Door Opener (Ref: AXT-VSDb)

2. Chicken Guard Automatic Door Opener - Standard AS (Ref: CGUARD-AS)

3. HempBed-E® Poultry Bedding 15kg (Ref: HBE15)

Price is per pulley.

Small plastic pulley to aid the placement of the VSB/VSD where it cannot be placed directly above the pop-hole door. Scroll down to our booklet for more information on placement. Pulleys are 35mm in diameter.

FSF Tip: If using pulleys with your unit you may require extra cord (see below) to attach to the main cord. This will make sure that you can still install the unit with the door in the open position and have the right amount of cord without a strain on the motor.

Related products:

1. Large Pulley for VSB & VSD Pop-hole Door Openers (Ref: VSBHS2)

2. VSB Automatic Pop-hole Door Opener - internal (Ref: VSBbi)

3. Spare Cord for VSB & VSD units, 2m (Ref: VSBC)

4. Lightweight Pop-hole Door for Auto Door Openers (Ref: VSBDOOR)

People who bought this item also bought:

1. Spare Cord for VSB & VSD units, 2m (Ref: VSBC)

2. Lightweight Pop-hole Door for Auto Door Openers (Ref: VSBDOOR)

3. VSD Auto Pop-hole Door Opener (Ref: AXT-VSDb)

Price is per pulley.

Large Pulley for use with the VSB & VSD Door Openers. The large pulley is placed at right angles to the house wall and is used for very large doors to give extra leverage or, where the cord needs to be held away from the house and perhaps changes direction through 180 degrees or to overcome an obstacle.

Aids the placement of the VSB/VSD for non-vertical pop-hole doors, or where there is non enough space above the pop-hole to attach the unit directly above the door. Extends 55mm. Bracket is 54mm wide x 43mm high.

Related products:

1. Small Pulley for VSB & VSD Pop-hole Door Openers (Ref: VSBPUL)

2. Replacement battery holder for VSB Units (Ref: VSB-BH)

3. Spare Cord for VSB & VSD units, 2m (Ref: VSBC)

4. VSB Automatic Pop-hole Door Opener - external (Ref: VSBb)

People who bought this item also bought:

1. Plastic Powder Shaker (Ref: 972546)

2. VSD Auto Pop-hole Door Opener (Ref: AXT-VSDb)

3. Diatomaceous Earth Powder (5kg tub) (Ref: DIAT5)

Pair of Red Magnets for VSD Door Opener Units on a metal strip for safety.

PRICE INCLUDES POSTAGE.

VSD Units come with one red magnet included. this pair is for replacement and comes with a metal strip and two screws to screw onto the henhouse and give them a home so they don't get lost.